More bits and pieces

Over the last few days I have been continuing the assembly of unseen parts. Last weekend my brother Ian called to say he was coming to the house. After he and Cindy arrived he said he needed a hand with something in the back of his car, and there was a new stainless exhaust front to back. Ian said happy birthday and merry Christmas, needless to say I am still in shock and disbelief.

I installed the down pipes today and a word to the wise remove the labels first I have seen several with square black spots where the labels were. What I did was warm them up with a heat gun this softens the glue so the label comes off easily if you are careful, the residue will come off with an orange cleaner ( GooGone)

Recently I have been following the Peking to Paris rally. There is a local car in it (041) and I think is is good to support our neighbors. The address is http://www.pekingparis.com/ and the local car is http://flora2010.blogspot.com/. I have had fun watching the progress and reading the blog entries of several entrants. Unit 028 has been replaced with a Healey since the original car was damaged, and they are just continuing with their friends even though they are out of the rally. Vewy interesting.

Any way on to my car. I have been busy finishing up small tasks that no one would notice even if I had a picture to show. Little things like the rear transmission mount, tightening bolts and screws, I also rebuilt the distributor, I ordered a new capacitor for it and it came in 4 pieces not quite what I expected, however a quick call to Moss and a chat with a delightful person a new one is on its way, great company to deal with.

I have bent a new heater core supply pipe from some soft copper pipe, not perfect but passable, I have also made a new fuel line between carbs much nicer than the original one. I have also installed the radiator and hoses. The dash went in last weekend and the control escutcheon are now in as well. Other small things include connecting the fresh air control cable the heater control cable and the heat control are done also. Misc oiling and greasing is also complete.

Even more gets done

I spent part of today to trim the mounting bolts the new ones were about 3/8th too long I also tightened up the rear mount also. I also installed the clutch slave and put the generator in place, I can't locate the bolt for this so I will make one later this week. All in all it has been a very productive day and I look forward to continuing the assembly later this week. As usual work gets in the way yet again.

Next big step is done

I went to Sidney yesterday to get a new satellite receiver from my best friend. On the way I stopped in to see if Jason was around. My older brother is having a BN6 restored for him in metallic light blue, I really wanted to see what his freshly painted chassis looked like.

Any way I mentioned that the engine was ready to go in, to which Jason said there is the engine lift and that he would be happy to help. I thought about it for about 5 nano seconds and asked if he was sure so the lift was put in my van and I took it home waiting for Sun afternoon.

This morning Laura (my wife) and I put the transmission and engine together. A couple of hours later Jason arrived and the install began there was only one or two small problems that only took minutes to overcome. It was obvious it was not Jason's first rodeo. An hour later it was in and secured ready for the next step of assembly. To me this was way over the top for Jason to help, I can't properly convey to him how much I appreciate his help. Thanks Jason.

Things are still progressing

I haven't been posting much as the progress has been hard to see. Lots of little steps and nothing that is noticeable on any pictures I have taken. But, the latest steps have been a little more noticeable, the installation of the drivers seat rails set, the passenger seat is fixed. I have used a new chrome source for the emergency brake handle, which I think turned out superb. These two changes have been quite welcome.

I have also finished cleaning and painting the transmission this week it is now ready to marry to the engine and then drop the whole assembly into the car. I replaced the rear seal, it was a challenge but I got it done and back together.

I painted the cross in front of the radiator black, this is one of those jobs I was not excited to do but turned out it was quite easy with good results. Surprising what a lot of masking tape and paper will accomplish. I also rebuilt the original fuel pump rather than use the new one I bought, since it didn't fit.

Captain there be wheels

Over the past few weeks I have been finishing up lots of little things to the car. There are just too many to mention also I can't remember all of them. The biggest was the coil springs for the front suspension, it took me almost 3 hours to do both sides but it was safe and the method was slick. I used two 8" pieces of 3/8 nf ready rod and tightened them up in unison.


After a lot of time and effort I now have a rolling chassis, YEHHHH, right now I have approximately 600 to 650 hours invested in the car. This covers things like deconstruction, cleaning, sandblasting, powder coating, and reassembly. The next big step is to install the engine and start getting it to the point of will it run?

Keep checking I will try to update more often in the future.

Continuing assembly

Over the last couple of weeks I have been trying to get the rear end assembled and installed in the car. Today I reached this goal and have put the rear wheels on. I have also installed the steering column with a small amount of frustration. Every thing has to be installed in the correct order otherwise you will be disassembling it again like I did.

The rear of the car except the fuel pump is complete, the engine compartment is about 90% complete. the next push for me is to finish the wiring and install the engine. I have the front suspension on and just need to finish installing the front breaks.